The Hurst® Roll/Control®, Line/Loc® for your 2011-2014 Dodge Challenger SRT8 is primarily used in drag racing to lock the front wheels allowing for more consistent burnouts when heating up the tires to make a pass. This kit comes with all the necessary parts needed to easily install a Hurst Line/Loc system on your Challenger SRT8. Includes a stainless steel Roll/Control valve, brake line, fittings, lighted momentary switch, bracket, wiring and much more. Rigorous testing has proved a 1/100,000 of a second release time and vibration tests have seen up to 30 G's applied without mechanical failure. Adaptable to most domestic and import hydraulic brake systems. Advanced quality design stainless steel valve assembly for ultimate corrosion resistance. Fully enclosed epoxy molded electrical coil for reliability. Attractive finned aluminum housing helps dissipate heat. Wider lightweight base provides better mounting stability 150 micron screen filtered ports to prevent contamination. Field serviceable for cleaning or rebuilding. Extra threaded port for separate bleeder or brake line pressure gauge Kit includes solenoid valve, snap-action switch, indicator light, 4-amp fuse, mounting screws and installation instructions. Note: Not recommended for use as a parking brake, or for longer then 60 seconds maximum at any one time.

Features:
The Hurst® Roll/Control®, Line/Loc® for your 2011-2014 Dodge Challenger SRT8 is primarily used in drag racing to lock the front wheels allowing for more consistent burnouts when heating up the tires to make a pass. This kit comes with all the necessary parts needed to easily install a Hurst Line/Loc system on your Challenger SRT8. Includes a stainless steel Roll/Control valve, brake line, fittings, lighted momentary switch, bracket, wiring and much more. Rigorous testing has proved a 1/100,000 of a second release time and vibration tests have seen up to 30 G's applied without mechanical failure. Adaptable to most domestic and import hydraulic brake systems. Advanced quality design stainless steel valve assembly for ultimate corrosion resistance. Fully enclosed epoxy molded electrical coil for reliability. Attractive finned aluminum housing helps dissipate heat. Wider lightweight base provides better mounting stability 150 micron screen filtered ports to prevent contamination. Field serviceable for cleaning or rebuilding. Extra threaded port for separate bleeder or brake line pressure gauge Kit includes solenoid valve, snap-action switch, indicator light, 4-amp fuse, mounting screws and installation instructions. Note: Not recommended for use as a parking brake, or for longer then 60 seconds maximum at any one time.

More From This Category

Wilwood KIT,REAR,EPB,FDP-LP,BIG FORD,2.36 OFFSET 1PC,11.00 ROTOR

Wilwood KIT,REAR,EPB,FDP-LP,BIG FORD,2.36 OFFSET 1PC,11.00 ROTOR

$3,705.10

DBA Street Series Master Cylinder, For Toyota, Kit

DBA Street Series Master Cylinder, For Toyota, Kit

$257.20

Strange ,Fitting, Master Cylinder, -3 AN Male Threads x 9/16-20 in. Male Threads, Stainless Steel, Natural, Each

Strange ,Fitting, Master Cylinder, -3 AN Male Threads x 9/16-20 in. Male Threads, Stainless Steel, Natural, Each

$22.59

Wilwood Bolt, 12 Point, Stainless, 18-8, 12 Point, 0.750 in. Length, 1/4-28 Thread, Kit

Wilwood Bolt, 12 Point, Stainless, 18-8, 12 Point, 0.750 in. Length, 1/4-28 Thread, Kit

$30.55

Strange ,Caliper bracket from B1700WC brake kit- ea

Strange ,Caliper bracket from B1700WC brake kit- ea

$119.85

DBA Front 4000 Series T3 Brake Rotor, 354mm, For Toyota Tundra 05-08 / Cruiser VDJ200 MY16, Kit

DBA Front 4000 Series T3 Brake Rotor, 354mm, For Toyota Tundra 05-08 / Cruiser VDJ200 MY16, Kit

$350.70